plane section

英 [pleɪn ˈsekʃn]

美 [pleɪn ˈsekʃn]

网络  水平断面

英英释义

noun

• (geometry) the area created by a plane cutting through a solid
  Synonym:section

双语例句

• Lately the work on hand is modelling pituitary in3D, here's a vertical plane section view.
  最近做下丘脑的三维建模，这是矢状面截面的模型。
• In related pilot study, more cross-section of the reinforcement has been researched, but it has few study in strengthen diagonal plane section.
  在相关的试验研究中，更多的是对正截面的加固研究，而对斜截面的抗剪加固试验研究还比较少。
• The results showed that reinforced concrete beam serviced 11 years and with a certain cumulative damnification is still basically in line with the plane section assumption. The old beam which appears a larger crack, deformation before destruction was still ductile.
  试验结果表明已经服役了11年且有一定累积损伤的钢筋混凝土旧梁仍然基本符合平截面假定，旧梁破坏前出现较大的变形和裂缝，破坏仍然呈延性性质。
• The test results indicate that the ultimate load bearing capacity and the behavior of deformation of the timber beams is greatly enhanced after strengthened by CFRP, and the longitudinal strains of intact beams and strengthened beams are all consistent with the assumption of plane section.
  试验结果表明，采取碳纤维布加固木梁，其承载力得到大幅度的提高，变形性能得到显著的改善，加固前后截面应变均符合平截面假定。
• According to the postulating of plane section and calculation sketch, the strain relation of Carbon Fiber Reinforced sheet and reinforcing steel are researched as well as the calculation methods of ultimate moment in this paper.
  本文根据碳纤维加固梁的平截面假定及其计算简图推导了碳纤维与钢筋应变之间的关系、以及抗弯承载力的计算方法。
• As to bonded concrete beams, complete bond between steel and concrete is always assumed, so analysis can be performed based on plane section hypothesis.
  对于有粘结混凝土梁，一般认为钢筋和混凝土之间理想粘结，从而可基于平截面假定进行分析。
• The Assumption of Plane Section and Its Application
  平截面假定及其应用
• A method to calculate the section curvature ductility index of high strength concrete shear wall is induced by using stress-strain relationship of rectangle stirrup and plane section assumption.
  利用矩形箍筋约束混凝土的应力一应变关系和平截面假定，建立了高强混凝土剪力墙截面曲率延性系数的计算方法。
• For NC machining of plane section method, the machining path of tool cutting plane and implicit surface can be found, and the curve of the tool path is drawn by the positive-negative method.
  把隐函数的优势应用到数控加工编程中，即对于截面法的数控加工，求出刀具切削平面与隐函数曲面的加工轨迹，再用正负法绘制刀具轨迹曲线。
• The superposition theory has the lower bound theorem of the plastic theory as its foundation. The simplified formula of the superposition theory is easy to use and its result is quite close to the accurate solution of the plane section method.
  结果表明，叠加方法不仅以塑性理论下限解为理论基础，且所得到的简化计算公式简便适用，与平截面法和规范方法计算结果的误差在工程可接受的范围内。